Aluminum fascia wrap is a formed metal cover bent to fit over the wood fascia board at your roof edge. It keeps rain and sun off the wood and ends repainting, but it only works over solid boards. Wrapped over rot, it hides the damage while the wood keeps failing underneath, and your gutters loosen with it.
Want someone to check your boards before anything gets covered? Call Cannon Roofing at (940) 627-1045 any time, or reach us through our contact page to set up a free inspection.
What aluminum fascia wrap does well
The fascia is the vertical board that caps the ends of the rafters and carries the gutters. On many North Texas homes it is painted wood, and in our sun the paint breaks down, the wood checks and cracks, and water from overflowing gutters soaks into the end grain. Wrapping the board in coil aluminum, bent on site to match its profile, puts a weatherproof skin over it.
- No more scraping and repainting the roof edge.
- Wood stays drier when water splashes or gutters overflow.
- Metal is harder for squirrels and woodpeckers to get through than paint and wood.
- Crisp, uniform lines, available in colors that match soffit and gutters.
When wrapping wood fascia makes sense
Wrap is a smart choice when the boards are sound, straight and dry, and you are tired of painting them. It is especially sensible when new gutters or new soffit are going on anyway, because the gutters come down and the edge is open for the work.
A simple board test
Press a screwdriver into the fascia at the bottom edge, near downspouts and at inside corners, which are the spots that stay wet longest. If the tip sinks in or the wood crumbles, that section is rotten. Also look for gutters that tilt forward, peeling paint in one area only, or dark streaks running down the board.
Why rotten boards must be replaced first
Covering rot is a common shortcut in fascia work. The metal looks new for a while, but trapped moisture keeps working on the wood. The gutter hangers are screwed through the wrap into that wood, so as it softens they loosen, the gutter sags, and water starts running behind it. By the time anyone notices, the damage can reach the rafter tails and the roof deck edge.
The right sequence is to remove the gutters, pull off any rotten fascia, check the rafter tails behind it, replace damaged boards with new lumber, and only then wrap. We go through this process in our article on rotted fascia behind gutters.
What we look for behind the board
Rafter tails with soft ends, sub-fascia that has separated, and deck edges darkened by water all need attention. Covering any of those with trim does not solve anything. We also look at why the wood got wet in the first place, whether that was an undersized gutter, a missing apron or a downspout that kept backing up, because the cause has to be fixed too.
How wrap works with gutters and drip edge
Fascia wrap does not replace roof edge flashing. The drip edge or gutter apron still has to sit on the roof deck under the shingles and direct water into the gutter. The wrap tucks up under that flashing, so water running off the roof lands on metal that sheds it downward, not into the joint behind the trim. If the wrap is installed over the drip edge instead of under it, water can get between the wrap and the wood and stay there. We cover the edge metal itself in drip edge, starter strips and roof edges.
Sequencing with new gutters
Gutters mount after the wrap is on. Hangers screw through the aluminum into solid wood, and each penetration should be tight and sealed where needed. Seamless gutters in a matching color finish the edge.
Details that separate good wrap from bad
- Laps overlap in the direction that sheds water, not against it.
- A hemmed lower edge for stiffness and no sharp raw metal.
- Fasteners placed to allow expansion, since Texas heat makes aluminum move and poorly nailed wrap ripples or buckles.
- Corners and gable ends shaped cleanly rather than stuffed with sealant.
Our approach at Cannon Roofing
Fascia wrap is part of our gutter, soffit and fascia service. We probe the boards, replace what is rotten, check the roof edge flashing and then wrap and rehang gutters as one coordinated job, so nobody has to come back and undo someone else's work. Cannon Roofing was founded in Decatur in 1994, our crews are factory trained, and each crew member holds the Technician Seal of Safety.
We do not publish prices, because the amount of board replacement, eave height, roof edge length and gutter work vary from house to house. Your estimate spells out what is being replaced and what is being wrapped. Call (940) 627-1045 to get yours started.
Frequently asked questions
How long does aluminum fascia wrap last?
Installed over sound, dry wood with proper flashing above, it can last for many years with little upkeep beyond washing. Its life depends mainly on keeping water out from behind it.
Can fascia be wrapped without taking the gutters down?
Not properly. The wrap has to go behind the gutter, so the gutters come down, and that is also the only good time to inspect the wood.
Is aluminum fascia wrap the same as vinyl fascia?
No. Vinyl fascia covers are available too, but aluminum bends to any profile, holds a crisp line and is commonly used where gutters hang from the board.
Thinking about wrapping your roof edge? Call Cannon Roofing first at (940) 627-1045, day or night. We will check every board, tell you plainly what needs replacing and give you a free estimate. You can also reach us on our contact page.